Time dependence of corrosion behavior on Ta in NaOH solutions

Ishijima, Yasuhiro; Ueno, Fumiyoshi; Abe, Hitoshi

Materials Transactions, 63(4), p.538 - 544, 2022/04

https://doi.org/10.2320/matertrans.MT-C2021005

The time dependence of the corrosion behavior of tantalum (Ta), which is used in nuclear fuel reprocessing equipment, in sodium hydroxide (NaOH) solutions was investigated by immersion tests, and the mechanism of the time dependence was examined via surface observations and electrochemical measurements. The immersion tests were conducted at room temperature with NaOH concentrations ranging from 1 to 7 mol/L for immersion periods of 24 to 168 h. The corrosion rate increased with the NaOH concentration but peaked with the immersion period and then decreased. The time to peak of the corrosion rate was shorter with higher NaOH concentration. The X-ray diffraction (XRD) patterns and Raman spectra of the surfaces of the specimens immersed in the 7 mol/L NaOH solution for more than 48 h showed NaTaO formation. The polarization resistance decreased with immersion time for all NaOH concentrations up to about 24 h after immersion. Thereafter, the polarization resistance increased with immersion time in 7 mol/L NaOH solution and remained almost constant in the other NaOH concentrations. Findings suggested that the change in the corrosion rate was affected by the film formation during immersion, since the time dependence of the polarization resistance and the sum of film resistance and charge transfer resistance had the same tendencies. The precipitation film was mainly NaTaO formed by the dissolution of the passivity film on Ta.

Time dependence of corrosion behavior on Ta in NaOH solutions

Ishijima, Yasuhiro; Ueno, Fumiyoshi; Abe, Hitoshi

Zairyo To Kankyo, 70(6), p.192 - 198, 2021/06

https://doi.org/10.3323/jcorr.70.192

The time dependence of corrosion behavior on tantalum used in nuclear fuel reprocessing equipment in sodium hydroxide solution was investigated by immersion corrosion tests, and the mechanism of aging change was discussed from surface observations and electrochemical measurements. The immersion tests were carried out at room temperature with NaOH concentrations ranging from 1 to 7 mol/L and immersion times ranging from 24 to 168 hr, respectively. The corrosion rate increased with NaOH concentration, but peaked with immersion time and then decreased. The time to peak of corrosion rate was shorter with higher NaOH concentration. The SEM observations and Raman analysis at the surface of the specimens that were cleaned and weighed after the immersion test did not show any film formation. On the other hand, the polarization resistance showed a constant value or an increase after a decrease immediately after immersion. It is suggested that the change in corrosion rate is affected by the formation of film by immersion, since the value of polarization resistance is almost the same as the sum of film resistance and charge transfer resistance. The film was considered to be mainly NaTaO formed by the dissolution of Ta.

Research development of separation for nuclear fuel reprocessing and reduction of hazardous substance in high level radioactive waste

Sasaki, Yuji

Kagaku Kogaku, 84(9), p.425 - 427, 2020/09

The reduction of waste volume and hazardous substance though separation methods concerning atomic energy must be requested. As disposal methods or temporary measures, geological disposal, transmutation and interim storage are proposed. In order to perform effectively the disposal methods, the development of separation method of aimed elements is indispensable. Here, the new separation method of U and Pu from spent nuclear fuel and minor actinide separation and fission products from high level radioactive waste are explained.

Estimation of corrosion mechanisms from the data obtained by the reproduced experiments considering the actual environments; Maritime structures and nuclear facilities

Yamamoto, Masahiro

Zairyo To Kankyo, 66(1), p.3 - 12, 2017/01

https://doi.org/10.3323/jcorr.66.3

The laboratory simulation tests which could be reproduced the corrosion reactions propagating in the actual environments were utilized to analyze the mechanism of corrosion phenomena. In this report, some results are introduced in the cases of maritime structures and nuclear facilities. Experimental apparatus was originally designed to obtain the data in high radioactive condition simulating actual plants. One is a result showing the effect of Np ion to the corrosion of stainless steel in nuclear fuel reprocessing plant. Corrosion mechanism was revealed that Np ion is reduced to Np ion by a corrosion reaction of stainless steel and then re-oxidized to Np ion in the bulk solution. And repetition of this cycle accelerated corrosion of stainless steel by a little amounts of Np addition in nitric acid solution. Another result is introduced that an effect of HO created by radiolysis of cooling water at high radioactive environment in light water reactor.

Handbook on Process and Chemistry of Nuclear Fuel Reprocessing, 3rd Edition

Committee of Handbook on Process and Chemistry of Nuclear Fuel Reprocessing

JAEA-Review 2015-002, 726 Pages, 2015/03

JAEA-Review-2015-002.pdf:43.63MB
JAEA-Review-2015-002(errata).pdf:0.21MB

The fundamental data on spent nuclear fuel reprocessing and related chemistry was collected and summarized as a new edition of "Handbook on Process and Chemistry of Nuclear Fuel Reprocessing". The purpose of this handbook is contribution to development of the fuel reprocessing and fuel cycle technology for uranium fuel and mixed oxide fuel utilization. Contents in this book was discussed and reviewed by specialists of science and technology on fuel reprocessing in Japan.

Proceedings of the 6th NUCEF Seminar; February 20, 2003, JAERI, Tokai, Japan

6th NUCEF Seminar Working Group

JAERI-Conf 2003-018, 132 Pages, 2003/10

JAERI-Conf-2003-018.pdf:10.41MB

no abstracts in English

Effects of a heat-transfer on corrosion of zirconium in a boiling nitric acid solution

Kato, Chiaki; Yano, Masaya*; Kiuchi, Kiyoshi; Sugimoto, Katsuhisa*

Zairyo To Kankyo, 52(1), p.35 - 43, 2003/01

http://joi.jlc.jst.go.jp/JST.Journalarchive/jcorr1991/52.35

The effects of heat-transfer on the corrosion of zirconium was examined in boiling nitric acid solutions with various concentrations. Corrosion mass losses and electrochemical polarization curves were measured on the heat-transfer and isothermal surfaces in the solutions. It was found that the corrosion rate of zirconium was higher on the heat-transfer surface than that on the isothermal surface. The rate increased with increasing nitric acid concentration and solution temperature. The increased oxidization potential on the heat-transfer surface is attributed to the reduction of nitrous acid concentration by the thermal decomposition on the surface and the removal of the decomposition product from solution by boiling bubbles. The redox potential of 12 mol/dm3 nitric acid on a boiling heat-transfer surface was very close to the breakdown potential of primary passivity of zirconium. This suggests the initiation of SCC on a boiling heat-transfer surface in a nuclear fuel reprocessing.

Annual report on the effluent control of Tokai Works FY 2001

Shinohara, Kunihiko; Takeishi, Minoru; ; ; Mizutani, Tomoko

JNC TN8440 2001-019, 141 Pages, 2001/11

JNC-TN8440-2001-019.pdf:12.69MB

This report was written about the effluent control in JNC Tokai Works from 1 April 2000 to 31 March 2001. In this period, the quantities and concentrations of retroactivities in liquid waste from Tokai Works were under the discharge limits of "Safety Regulations for the Tokai Reprocessing Plant", "Safety Regulations for the Tokai Reprocessing Plant" and regulations of government.

Study of uranium particle fuel fabrication with the external gelation process with the vibration dropping Method

Nishimura, Kazuhisa; Shoji, Shuichi*; *; Sato, Seiichi*; ; Endo, Hideo

JNC TN8430 2001-005, 64 Pages, 2001/09

JNC-TN8430-2001-005.pdf:4.1MB

The external gelation process is one of the candidates of MOX particle fuel fabrication for advanced recycle system. It was necessary to perform preliminary fuel fabrication with uranium before starting MOX tests. As the result of the preliminary examination, Basics conditions of the fabrication were obtained: (1)Optimized uranyl nitrate solution and PVA solution, as raw materials were prepared. (2)The frequency of vibration and the amount of flow were obtained with optimized broth (mixture) in the vibration dropping process. (3)The influence of composition of broth and concentration of ammonia solution on gelation process was obtained. (4)Impurities after aging, washing and drying spHerical gel were surveyed, (5)The spherical gel were calcined to oxide particles and the particles were characterized by TG-DTA, therefore it is certain that outlook on the sintered particles as final products is very clear. On the top of that, there were no fatal technicalities of the external gelation process through material balance and a diameter dispersion of spherical gel and oxide particles. It is necessary to perform uranium examination to solve some new problems, for instant, surface crack of spherical gel. Although almost of all the preparations are completed and fabrication examination of MOX particles with vibration dropping equipment are ready for starting.

Manufacture history results of an investigation of the bitumen solidification object towards the check of an abandonment object

; Kondo, Toshiyuki; *

JNC TN8440 2001-024, 210 Pages, 2001/08

JNC-TN8440-2001-024.pdf:24.99MB

In order to make this book reflect in the investigation which turned the bitumen solidification object to maintenance of the abandonment object technical standard on condition of carrying out subterranean disposal in the future - solidification - it created for the purpose of utilizing as precious sources of information, such as a nuclide inventory in the living body, group-izing of the past campaign required for typical solidification object selection, and information offer at the time of disposal examination. A development operation history collected so that histories including the shift action in an institution of the formation of discharge reduction of the characteristic of solidification object manufacture outlines, such as composition of the process of an institution and a solidification object and a storage actual result, the contents of an examination of the past campaign, and the solidification object manufactured based on topics or radioactive iodine and radioactive carbon etc., such as the past contents of an examination / operation, may grasp comprehensively in creation, and it carried out as the composition stared the trend of future disposal fixedly. It was a period (for 16 years) until an bituminization demonstration facility processing institution will start a cold examination from April (Showa 57), 1982, and it starts a hot examination from May 4, it starts solidification processing technical development operation from october 6 and it results in the fire explosion accident on March 11 (Heisei 9), 1997, and low level radioactivity concentration waste fluid was processed 7,438 m, and 29,967 bitumen solidification objects were manufactured. According to the accident, it is necessary to hand it down to future generations with processing technology while the bitumen solidification object manufactured in 15 years although the bituminization demonstration facility processing institution came to close the mission holds information precious ...